Permanent Bracelet Kit: Easy At-Home Fitting Guide

Looking to create a lasting memory with someone special? With the Allure Permanent Bracelet Kit, you can now create your own forever bracelets at home – no need for an expensive trip to the jeweller.

Whether it’s with your partner, best friend or sibling, this easy-to-use permanent bracelet kit gives you the chance to create a shared symbol of connection from the comfort of your own home. In this blog, we’ll walk you through everything you need to know to safely and securely fit your Allure permanent bracelet.

What Is a Permanent Bracelet?

A permanent bracelet is a dainty chain bracelet that’s permanently closed, meaning it has no clasp and is designed to be worn 24/7. The idea is simple – a bracelet that’s meant to be as lasting as the bond it represents.

With Allure Jewellery, you can now create this experience at home using our purpose-built Permanent Bracelet Kit. The kit includes everything you need to cut and secure your own bracelet on yourself or someone else, with no prior experience needed.

What’s Inside the Allure Permanent Bracelet Kit?

Your Allure kit arrives with everything required to complete the process from start to finish:

✔️ 2x Bracelets Chains – Choose between Silver, Gold or one of each
✔️ 2x Jump Rings – These are attached to one end of each chain ready to be worn
✔️ 1x Cutters – Used to cut the bracelet down to the correct length
✔️ 1x Pliers – Used to close the special clasp and lock your bracelet into place

Step-by-Step Guide: How to Fit Your Bracelet

Before you begin, choose a well-lit workspace like a table or desk, and read through the full steps once to get familiar. This is a two-person activity — one person will wear the bracelet, and the other will do the welding.

Step 1: Set Up Your Workspace

Lay out all kit components on a clean, flat surface.
Using a well lit area will help you when closing the small clasp later.

Step 2: Size Your Bracelet

Wrap the bracelet around the wearer’s wrist to find the perfect fit. You’re looking for snug but not tight – it should sit naturally without sliding down too far. Bear in mind, once the bracelet is on it cannot be adjusted.
Once you are happy with the length, cut the bracelet using the cutters provided. This can be tough and may take multiple attempts to cut through the chain.

✅ Tip: If you’re unsure, it’s better to start a little longer – you can always trim more.

Step 3: Open The Jump Ring

Bend open the clasp using the pliers and your finger just enough so the other end of the chain will be able to hook onto it.
Make sure not to bend the jump ring too far open as the point needs to align and go through the hole to lock it back into place.

Step 4: Fit The Bracelet On Your Wrist

Wrap the bracelet around your wrist and hook the end of the chain onto the open clasp.

Step 6: Close The Clasp

Once the bracelet is in place on your wrist, using the pliers squeeze both ends of the claps together so that the pin goes through the hole opposite.
Once the clasp is fully closed, the bracelet is locked into place and will not come off.

Now you’re done! 🎉

Tips for a Smooth Experience

Make it fun – light a candle, put on music, and treat it like a mini date night or bonding moment.
Double and triple check the length of the bracelet before cutting.
Don’t over bend the locking clasp – only open it enough to allow the chain to hook onto it, this way it will be easier to close the clasp again.

FAQs: What Customers Ask Most

Can I take the bracelet off later?
No – the idea is that it’s permanent. However, if you really need to remove your bracelet they can be cut off using the cutters we provide.

Can I wear it in water?
Yes – the chains are water-resistant and fine to wear in the shower, pool or sea.

Can I travel with a permanent bracelet?
Yes. Permanent bracelets do not set off metal detectors and are allowed in UK and international airports.

👉 Shop the Allure Permanent Bracelet Kit Now